도구 131 / 136

Closure Order with Rejection Allowance Calculator — US Units

Closure Order with Rejection Allowance connects the figures on a US supplier quote with the quantity used by your packaging operation. Have good closures required (units), expected closure rejection (%), closures per supplier carton (units) ready before you start.

사양 입력

개
%
개
입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

구매할 마개 수

52,000.00 개
정수 상자 수26.00 상자
예상 사용 가능 잉여량1,480.00 개

완제품 단위당 마개 한 개가 필요합니다.

불량률은 총구매 마개에 적용되며 교체는 없습니다.

별도 최소 주문량이나 생산 시동 여유는 포함하지 않습니다.

상자 수 = ceil(합격 목표량 ÷ (1 − 불량률/100) ÷ 상자당 수량)

Good closures required: 50000 units; Expected closure rejection: 1 %; Closures per supplier carton: 2000 units → 52,000.00 개

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

상자 수 = ceil(합격 목표량 ÷ (1 − 불량률/100) ÷ 상자당 수량)

The result answers a specific purchasing question: Work out closure order with rejection allowance with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read closures to purchase in units. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Good closures required (units); Expected closure rejection (%); Closures per supplier carton (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review closures to purchase and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter good closures required 50,000.00 units, expected closure rejection 1.00 %, closures per supplier carton 2,000.00 units. The calculated closures to purchase is 52,000.00 units. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

필요한 양품 마개 수
50,000 개
예상 마개 불량률
1 %
공급업체 상자당 마개 수
2,000 개
Cartons = ceil(Good target ÷ (1 − Rejection/100) ÷ Carton quantity)
구매할 마개 수52,000.00 개

자주 묻는 질문

Which units should I use for closure order with rejection allowance?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two closure order with rejection allowance results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record good closures required (units), expected closure rejection (%), closures per supplier carton (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗