도구 57 / 136

Material Required for Order Calculator — US Units

Material Required for Order connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good finished units (units), web width (inch), print / pack repeat (inch) ready before you start.

사양 입력

개
lanes
g/m²

공급업체의 실제 평량 또는 실측 평량이 있으면 사용하세요.

%

총투입량 대비 손실 비율입니다.

입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

필요한 총필름 투입량

1,856.52 lb
필요한 총필름 면적113,304.32 ft²
필요한 총원단 길이43,168.95 ft
총투입 환산 수량105,263.16 개

손실률은 총재료 투입량 중 손실되는 비율입니다. 총필요량 = 순필요량 ÷ (1 − 손실률)입니다.

원단 폭과 반복 길이에는 실제 생산 배부를 반영해야 합니다. 추가 고정 설정 손실은 별도로 계획하세요.

Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12

Target good finished units: 100000 units; Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Process waste: 5 % → 1,856.52 lb

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12

The result answers a specific purchasing question: Work out material required for order with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross film required in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Target good finished units (units); Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Process waste (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross film required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter target good finished units 100,000.00 units, web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes. The calculated gross film required is 1,856.52 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

목표 양품 완제품 수
100,000 개
원단 폭
31.496063 inch
인쇄 / 포장 반복 길이
9.84251969 inch
원단 폭 방향의 열 수
2 lanes
필름 평량
80 g/m²
공정 손실
5 %
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12
필요한 총필름 투입량1,856.52 lb

자주 묻는 질문

Which units should I use for material required for order?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two material required for order results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good finished units (units), web width (inch), print / pack repeat (inch), lanes across the web (lanes) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗