Molded Fiber Tooling Amortization Calculator — US Units
Molded Fiber Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have mold / die cost (currency), initial setup cost (currency), expected lifetime items (units) ready before you start.
사양 입력
단위 표시만 하며 통화 변환은 하지 않습니다.
제품당 원가
전체 수명 생산량은 계획 가정입니다. 입력 금액에 포함하지 않았다면 교체 금형과 반복 설정 비용은 제외됩니다.
트레이 견적에 금형비가 이미 포함되어 있으면 이 배부액을 다시 더하지 마세요.
개당 금형비 = (금형 또는 칼형 + 초기 준비) ÷ 예상 수명 수량; 1,000개당 = 개당 금형비 × 1,000
Mold / die cost: 1500 USD; Initial setup cost: 500 USD; Expected lifetime items: 100000 units → US$0.02000/개입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.
계산식을 알기 쉽게.
The result answers a specific purchasing question: Work out molded fiber tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per item in your selected currency/item. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
계산기 사용 방법
- 01
Collect Mold / die cost (currency); Initial setup cost (currency); Expected lifetime items (units). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review cost per item and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
검증할 수 있는 계산
For this US purchasing example, enter mold / die cost US$1,500.00, initial setup cost US$500.00, expected lifetime items 100,000.00 units. The calculated cost per item is US$0.02000/item. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 금형 / 절단 금형 비용
- 1,500 USD
- 초기 설정 비용
- 500 USD
- 수명 동안 예상 제품 수
- 100,000 개
Tooling cost/item = (Mold or die cost + Initial setup) ÷ Expected lifetime items; Tooling cost/1,000 = Tooling cost/item × 1,000자주 묻는 질문
Which units should I use for molded fiber tooling amortization?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two molded fiber tooling amortization results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record mold / die cost (currency), initial setup cost (currency), expected lifetime items (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.
계산 방법, 단위 및 재료 가정 ↗