Packaging Cost per Unit Calculator — US Units
Packaging Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), print / pack repeat (inch), lanes across the web (lanes) ready before you start.
사양 입력
공급업체의 실제 평량 또는 실측 평량이 있으면 사용하세요.
통화 표시만 변경합니다. 환율 환산은 하지 않습니다.
총투입량 대비 손실 비율입니다.
양품 포장당 재료 원가
손실률은 총재료 투입량 중 손실되는 비율입니다. 총필요량 = 순필요량 ÷ (1 − 손실률)입니다.
재료 원가만 포함하며 금형·판, 운송, 가공 인건비 및 부속품은 제외합니다.
Cost/good unit = Width(in) × Repeat(in) ÷ 144 ÷ Lanes ÷ (1 − Waste fraction) × Price/ft²
Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process waste: 5 % → US$0.02526/pack입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.
계산식을 알기 쉽게.
The result answers a specific purchasing question: Work out packaging cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read material cost per good pack in your selected currency/pack. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
계산기 사용 방법
- 01
Collect Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Film price on selected basis (currency/lb); Process waste (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review material cost per good pack and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
검증할 수 있는 계산
For this US purchasing example, enter web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes, film gsm 80.00 g/m². The calculated material cost per good pack is US$0.02526/pack. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 원단 폭
- 31.496063 inch
- 인쇄 / 포장 반복 길이
- 9.84251969 inch
- 원단 폭 방향의 열 수
- 2 lanes
- 필름 평량
- 80 g/m²
- 선택 기준의 필름 가격
- 1.36077711 USD/lb
- 공정 손실
- 5 %
Cost/good unit = Width(in) × Repeat(in) ÷ 144 ÷ Lanes ÷ (1 − Waste fraction) × Price/ft²자주 묻는 질문
Which units should I use for packaging cost per unit?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two packaging cost per unit results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), print / pack repeat (inch), lanes across the web (lanes), film gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.
계산 방법, 단위 및 재료 가정 ↗