도구 36 / 136

Roll Diameter from Length Calculator — US Units

Roll Diameter from Length connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll length (ft), film thickness (mil), core outer diameter (inch) ready before you start.

사양 입력

지관의 내경이 아닌 외경을 측정하세요.

입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

롤 예상 외경

13.06 inch

두께가 균일하고 단단히 감겼으며 공기층이 없다고 가정한 기하학적 추정입니다. 실제 원단 길이는 다를 수 있습니다.

지관 외경을 사용하며 공칭 내경으로 대신할 수 없습니다.

Roll OD(in) = √(Core OD(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

Roll length: 3280.839895013123 ft; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 13.06 inch

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

Roll OD(in) = √(Core OD(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

The result answers a specific purchasing question: Work out roll diameter from length with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Roll length (ft); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter roll length 3,280.84 ft, film thickness 3.15 mil, core outer diameter 3.54 inch. The calculated estimated roll outer diameter is 13.06 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

롤 길이
3,280.8399 ft
필름 두께
3.1496063 밀
지관 외경
3.54330709 inch
Roll OD(in) = √(Core OD(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
롤 예상 외경13.06 inch

자주 묻는 질문

Which units should I use for roll diameter from length?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll diameter from length results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll length (ft), film thickness (mil), core outer diameter (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗