FERRAMENTA 81 / 136

Carton Tooling Amortization Calculator — US Units

Carton Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have cutting die (currency), printing plates (currency), foil tooling (currency) ready before you start.

As suas especificações

USD
USD
USD
USD
USD
unidades

Apenas rótulo da unidade. Sem conversão cambial.

Os resultados atualizam-se ao editar. Nada é guardado até decidir fazê-lo.
Cálculo em tempo real

Custo por embalagem de cartão

US$0,00180/carton
Custo por 1.000 embalagens de cartãoUS$1,8000/1,000 carton
Total de ferramentas e preparaçãoUS$1.800,00

Pressupõe a produção da quantidade introduzida ao longo da vida útil. Não inclui substituições posteriores das ferramentas.

Ferramentas/unidade = (Cortante + Chapas + Ferramenta de estampagem + Ferramenta de relevo + Outra preparação) ÷ Quantidade de alocação

Cutting die: 1200 USD; Printing plates: 600 USD; Foil tooling: 0 USD; Embossing tooling: 0 USD; Other setup: 0 USD; Expected lifetime cartons: 1000000 units → US$0,00180/carton

Calculado a partir dos seus dados. Confirme as especificações com o fornecedor.

A fórmula explicada.

Ferramentas/unidade = (Cortante + Chapas + Ferramenta de estampagem + Ferramenta de relevo + Outra preparação) ÷ Quantidade de alocação

The result answers a specific purchasing question: Work out carton tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per carton in your selected currency/carton. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Como utilizar esta calculadora

  1. 01

    Collect Cutting die (currency); Printing plates (currency); Foil tooling (currency); Embossing tooling (currency); Other setup (currency); Expected lifetime cartons (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per carton and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Um cálculo que pode verificar

For this US purchasing example, enter cutting die US$1,200.00, printing plates US$600.00, foil tooling US$0.00000, embossing tooling US$0.00000. The calculated cost per carton is US$0.00180/carton. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Cortante
1.200 USD
Chapas de impressão
600 USD
Ferramentas de estampagem com película
0 USD
Ferramentas de relevo
0 USD
Outra preparação
0 USD
Caixas previstas durante a vida útil
1.000.000 unidades
Tooling/unit = (Die + Plates + Foil tooling + Embossing tooling + Other setup) ÷ Allocation quantity
Custo por embalagem de cartãoUS$0,00180/carton

Perguntas frequentes

Which units should I use for carton tooling amortization?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two carton tooling amortization results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record cutting die (currency), printing plates (currency), foil tooling (currency), embossing tooling (currency) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifique a fórmula, as unidades e os pressupostos apresentados antes de utilizar o resultado.

Método, unidades e pressupostos dos materiais ↗