Roll Diameter from Weight Calculator — US Units
Roll Diameter from Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have net film weight (lb), web width (inch), film gsm (g/m²) ready before you start.
As suas especificações
Utilize a gramagem real do fornecedor ou medida, quando disponível.
Meça o exterior do mandril, não o seu furo.
Diâmetro exterior estimado do rolo
Estimativa geométrica: pressupõe espessura uniforme, enrolamento apertado e ausência de ar retido. O comprimento real pode variar.
Utiliza-se o diâmetro EXTERIOR do mandril; o furo nominal não o substitui.
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
Net film weight: 176.36980974790205 lb; Web width: 31.496062992125985 inch; Film GSM: 80 g/m²; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 14,49 inchCalculado a partir dos seus dados. Confirme as especificações com o fornecedor.
A fórmula explicada.
The result answers a specific purchasing question: Work out roll diameter from weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
Como utilizar esta calculadora
- 01
Collect Net film weight (lb); Web width (inch); Film GSM (g/m²); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Um cálculo que pode verificar
For this US purchasing example, enter net film weight 176.37 lb, web width 31.50 inch, film gsm 80.00 g/m², film thickness 3.15 mil. The calculated estimated roll outer diameter is 14.49 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Massa líquida do filme
- 176,36981 lb
- Largura da banda
- 31,496063 inch
- Gramagem do filme
- 80 g/m²
- Espessura do filme
- 3,1496063 mil
- Diâmetro EXTERIOR do núcleo
- 3,54330709 inch
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)Perguntas frequentes
Which units should I use for roll diameter from weight?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two roll diameter from weight results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record net film weight (lb), web width (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Verifique a fórmula, as unidades e os pressupostos apresentados antes de utilizar o resultado.
Método, unidades e pressupostos dos materiais ↗