ИНСТРУМЕНТ 131 / 136

Closure Order with Rejection Allowance Calculator — US Units

Closure Order with Rejection Allowance connects the figures on a US supplier quote with the quantity used by your packaging operation. Have good closures required (units), expected closure rejection (%), closures per supplier carton (units) ready before you start.

Ваши параметры

шт.
%
шт.
Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Крышек к закупке

52 000,00 шт.
Целых коробок26,00 кор.
Ожидаемый пригодный излишек1 480,00 шт.

На каждую готовую единицу нужна одна крышка.

Брак применяется к общему количеству закупленных крышек без замены.

Отдельный MOQ или запас на запуск производства не включён.

Коробки = ceil(Требуемые годные единицы ÷ (1 − Брак/100) ÷ Количество в коробке)

Good closures required: 50000 units; Expected closure rejection: 1 %; Closures per supplier carton: 2000 units → 52 000,00 шт.

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Коробки = ceil(Требуемые годные единицы ÷ (1 − Брак/100) ÷ Количество в коробке)

The result answers a specific purchasing question: Work out closure order with rejection allowance with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read closures to purchase in units. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Good closures required (units); Expected closure rejection (%); Closures per supplier carton (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review closures to purchase and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter good closures required 50,000.00 units, expected closure rejection 1.00 %, closures per supplier carton 2,000.00 units. The calculated closures to purchase is 52,000.00 units. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Требуемое количество годных крышек
50 000 шт.
Ожидаемый брак крышек
1 %
Крышек в коробке поставщика
2 000 шт.
Cartons = ceil(Good target ÷ (1 − Rejection/100) ÷ Carton quantity)
Крышек к закупке52 000,00 шт.

Частые вопросы

Which units should I use for closure order with rejection allowance?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two closure order with rejection allowance results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record good closures required (units), expected closure rejection (%), closures per supplier carton (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗