TOOL 37 / 136

Roll Weight from Diameter Calculator — US Units

Roll Weight from Diameter connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.

Your specifications

Measure the outside of the core, not its bore.

g/m²

Use actual supplier or measured GSM when available.

Results update as you edit. Nothing is saved until you choose to.
Live calculation

Estimated net film weight

158.47 lb
Estimated roll length3,684.77 ft
Estimated film area9,671.33 ft²

Geometric estimate: assumes uniform thickness, a tightly wound roll and no entrained air. Actual running length may differ.

Core OUTER diameter is used; a nominal core bore is not a substitute.

Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436

Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 158.47 lb

Calculated from your inputs. Confirm specifications with your supplier.

The formula, made clear.

Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436

The result answers a specific purchasing question: Work out roll weight from diameter with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated net film weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

How to use this calculator

  1. 01

    Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated net film weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

A calculation you can check

For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated net film weight is 158.47 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Roll outer diameter
13.7795276 inch
Core OUTER diameter
3.54330709 inch
Film thickness
3.1496063 mil
Web width
31.496063 inch
Film GSM
80 g/m²
Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436
Estimated net film weight158.47 lb

Frequently asked questions

Which units should I use for roll weight from diameter?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll weight from diameter results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Check the displayed formula, units and assumptions before using the result.

Method, units and material assumptions ↗