工具 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

您的规格参数

件
件
g/m²
g/m²
%
修改参数时结果会自动更新。仅在您选择保存时才会保存。
实时计算

成型及封盖材料毛用量合计

95.15 lb
每幅卷材的展开毛长度1,151.17 ft
成型材料毛用量81.22 lb
封盖材料毛用量13.92 lb
每幅卷材毛面积1,133.04 ft²

损耗是总投入量中损失的比例。毛需求量=合格产出÷(1-损耗百分数/100)。

此规划模型假设成型与封盖卷材的幅宽和步距相同。固定开机损耗另行加入;需求为连续毛材料量,未按完整机器周期取整。

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95.15 lb

根据您输入的数据计算。请与供应商确认规格。

公式解释。

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

如何使用此计算器

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

可以核验的计算

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

目标合格包装数量
10,000 件
共用卷材宽度
11.8110236 inch
机器步距
3.93700787 inch
横向包装数量
3 件
成型卷材克重
350 g/m²
封盖材料克重
60 g/m²
总投入工艺损耗
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
成型及封盖材料毛用量合计95.15 lb

常见问题

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

使用结果前,请核对显示的公式、单位和假设。

方法、单位和材料假设 ↗