Laminate GSM Calculator — US Units
Laminate GSM connects the figures on a US supplier quote with the quantity used by your packaging operation. Build the structure or component list from the supplied specification.
逐层构建结构。
典型密度。实际密度随树脂牌号和配方而变化;如有供应商数据或实测数据,请优先使用。 实测克重或供应商克重通常比按密度推算更可靠。自定义材料请使用核实后的密度。不要用通用密度估算纸张克重。
胶黏剂、印刷和涂层
不计入的添加物请输入零。所有克重均为每平方米保留的干质量。 不根据克重推算胶黏剂、油墨和涂层厚度。
保留干涂层量
保留干质量
保留干质量
保留干质量
- 薄膜层
- 71.88 g/m²
- 胶黏剂、油墨、涂层及其他
- 2.00 g/m²
- 复合材料单位质量面积
- 66.09 ft²/lb
- 仅薄膜厚度
- 2.83 mil
- 每1,000平方米重量
- 162.88 lb
| 层/添加物 | 干克重 |
|---|---|
| 1. PET / BOPET | 16.68 |
| 2. PE(通用) | 55.20 |
| Adhesive interface 1 | 2.00 |
| 油墨 · 未计入 | 0.00 |
| 涂层 · 未计入 | 0.00 |
| 其他保留材料 · 未计入 | 0.00 |
| 合计 | 73.88 |
薄膜厚度不含胶黏剂、油墨和涂层厚度。收得量为工艺损耗前的理论值。 此估算采用材料库中的典型密度。
公式及代入值
Layer GSM = Thickness(mil) × 25.4 × Density(g/cm³). Total GSM includes dry retained additions.
Yield(ft²/lb) = 4,882.427636 ÷ Total GSM. Material $/ft² = GSM × 0.0002048161436 × Material $/lb.
PET / BOPET: 0.4724 mil × 25.4 × 1.39 = 16.68 g/m²
PE(通用): 2.36 mil × 25.4 × 0.9200 = 55.20 g/m²
Total retained basis weight: 73.88 g/m²
Yield: 4,882.427636 ÷ 73.88 = 66.09 ft²/lb
公式解释。
Build laminate gsm from the actual layer or component records rather than a generic material assumption. Enter dimensional specifications in the displayed US units and keep every price paired with its stated denominator. Review the layer contributions and the finished result together before comparing suppliers.
如何使用此计算器
- 01
Choose the actual materials or components and record their quantities, prices and retained additions.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review each contribution, then compare the total at the same production quantity and cost boundary.
可以核验的计算
The worked US scenario below keeps the supplied components, cost boundary and physical quantities explicit. Its dollar prices are illustrative, independent of the interactive example.
This independent 2-ply example has a 0.5-mil PET face at 1.39 g/cm³ and 1 PE layer at 1 mil and 0.92 g/cm³ each. Every interface adds 2 dry GSM of adhesive.
- PET price
- $2/lb
- PE price
- $1.25/lb
- Wet adhesive
- $2/lb · 40% solids
- Total basis weight
- 43.02 g/m²
- Coverage yield
- 113.49 ft²/lb
- Material cost
- US$0.01526/ft²
Layer GSM = mil × 25.4 × density; Yield(ft²/lb) = 4,882.427636 ÷ Total GSMThese are theoretical material figures. Converting loss, labor, energy and freight are excluded. Dry adhesive is retained mass; its purchased wet mass is divided by 0.40.
常见问题
Which units should I use for laminate gsm?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two laminate gsm results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record the component structure and cost basis for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
使用结果前,请核对显示的公式、单位和假设。
方法、单位和材料假设 ↗