Material Required for Order Calculator — US Units
Material Required for Order connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good finished units (units), web width (inch), print / pack repeat (inch) ready before you start.
您的规格参数
如有供应商提供的实际克重或实测克重,请优先使用。
占总投入量的损耗百分比。
所需薄膜毛用量
损耗率是损失材料占总投入材料的百分比。毛需求量=净需求量÷(1-损耗率)。
幅宽和重复长度应包含实际生产分摊。任何额外固定调机损耗应另行规划。
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12
Target good finished units: 100000 units; Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Process waste: 5 % → 1,856.52 lb根据您输入的数据计算。请与供应商确认规格。
公式解释。
The result answers a specific purchasing question: Work out material required for order with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross film required in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
如何使用此计算器
- 01
Collect Target good finished units (units); Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Process waste (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review gross film required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
可以核验的计算
For this US purchasing example, enter target good finished units 100,000.00 units, web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes. The calculated gross film required is 1,856.52 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 目标合格成品数
- 100,000 件
- 幅宽
- 31.496063 inch
- 印刷/包装节距
- 9.84251969 inch
- 幅宽方向的列数
- 2 lanes
- 薄膜克重
- 80 g/m²
- 工艺损耗
- 5 %
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12常见问题
Which units should I use for material required for order?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two material required for order results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good finished units (units), web width (inch), print / pack repeat (inch), lanes across the web (lanes) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
使用结果前,请核对显示的公式、单位和假设。
方法、单位和材料假设 ↗