工具 87 / 136

Shrink Sleeve Cost per Unit Calculator — US Units

Shrink Sleeve Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have layflat width (inch), sleeve cut length (inch), film gsm (g/m²) ready before you start.

您的规格参数

g/m²
USD/lb
%
USD/unit

仅为单位标识,不进行货币换算。

修改参数时结果会自动更新。仅在您选择保存时才会保存。
实时计算

每个合格套标的薄膜材料成本

US$0.00616/sleeve
每1,000个合格套标的薄膜材料US$6.1579/1,000 sleeves
含已输入加工费,每个套标US$0.00616/sleeve
展开筒膜理论面积0.3229 ft²/sleeve
每个套标的理论薄膜质量0.004299 lb/sleeve
每个合格套标的薄膜毛用量分摊0.004525 lb/sleeve
所用薄膜克重65.00 g/m²

平折宽为展开管周长的一半,因此面积包含两面。额外接缝搭接或切边不在此理论几何范围内。

损耗是总投入量中损失的比例。毛需求量=合格产出÷(1-损耗百分数/100)。

接缝、印刷和加工费用需另行输入。

Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)

Layflat width: 3.937007874015748 inch; Sleeve cut length: 5.905511811023622 inch; Film GSM: 65 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process loss on gross input: 5 %; Additional seaming / printing / conversion per sleeve: 0 USD/unit → US$0.00616/sleeve

根据您输入的数据计算。请与供应商确认规格。

公式解释。

Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)

The result answers a specific purchasing question: Work out shrink sleeve cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read film material cost per good sleeve in your selected currency/sleeve. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

如何使用此计算器

  1. 01

    Collect Layflat width (inch); Sleeve cut length (inch); Film GSM (g/m²); Film thickness (mil); Entered film density (g/cm³); Film price on selected basis (currency/lb); Process loss on gross input (%); Additional seaming / printing / conversion per sleeve (currency/unit). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review film material cost per good sleeve and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

可以核验的计算

For this US purchasing example, enter layflat width 3.94 inch, sleeve cut length 5.91 inch, film gsm 65.00 g/m², film price on selected basis US$1.3608/lb. The calculated film material cost per good sleeve is US$0.00616/sleeve. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

平折宽度
3.93700787 inch
套标切长
5.90551181 inch
薄膜克重
65 g/m²
所选基础的薄膜价格
1.36077711 USD/lb
总投入工艺损耗
5 %
每套标额外制缝/印刷/加工费
0 USD/单位
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)
每个合格套标的薄膜材料成本US$0.00616/sleeve

常见问题

Which units should I use for shrink sleeve cost per unit?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two shrink sleeve cost per unit results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record layflat width (inch), sleeve cut length (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

使用结果前,请核对显示的公式、单位和假设。

方法、单位和材料假设 ↗