工具 93 / 136

Thermoforming Sheet Weight Calculator — US Units

Thermoforming Sheet Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have sheet / web width (inch), sheet / web length (ft), sheet thickness (mil) ready before you start.

您的规格参数

g/cm³

示例密度。请使用实际聚合物或配方规格。

典型密度。实际密度随树脂牌号和配方变化。您可以修改上方数值。

修改参数时结果会自动更新。仅在您选择保存时才会保存。
实时计算

片材或卷材材料重量

1,190.50 lb
计算片材克重675.00 g/m²
片材或卷材面积8,611.13 ft²

密度需手动输入,不从成品零件推算。发泡或多层片材可能需要实测有效密度或实际克重。

Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436

Sheet / web width: 31.496062992125985 inch; Sheet / web length: 3280.839895013123 ft; Sheet thickness: 19.68503937007874 mil; Actual or assumed sheet density: 1.35 g/cm³ → 1,190.50 lb

根据您输入的数据计算。请与供应商确认规格。

公式解释。

Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoforming sheet weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read sheet / web material weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

如何使用此计算器

  1. 01

    Collect Sheet / web width (inch); Sheet / web length (ft); Sheet thickness (mil); Actual or assumed sheet density (g/cm³). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review sheet / web material weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

可以核验的计算

For this US purchasing example, enter sheet / web width 31.50 inch, sheet / web length 3,280.84 ft, sheet thickness 19.69 mil, actual or assumed sheet density 1.35 g/cm³. The calculated sheet / web material weight is 1,190.50 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

片材/卷材宽度
31.496063 inch
片材/卷材长度
3,280.8399 ft
片材厚度
19.6850394 密耳
片材实际或假定密度
1.35 g/cm³
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436
片材或卷材材料重量1,190.50 lb

常见问题

Which units should I use for thermoforming sheet weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoforming sheet weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record sheet / web width (inch), sheet / web length (ft), sheet thickness (mil), actual or assumed sheet density (g/cm³) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

使用结果前,请核对显示的公式、单位和假设。

方法、单位和材料假设 ↗