ツール 95 / 136

Thermoforming Scrap Rate Calculator — US Units

Thermoforming Scrap Rate connects the figures on a US supplier quote with the quantity used by your packaging operation. Have gross sheet input weight (lb), actual good part weight (lb), good parts produced (units) ready before you start.

仕様を入力

個
入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

総投入量に対するスクラップ率

20.00 %
良品出力に含まれない材料220.46 lb
良品完成品の出力重量881.85 lb
工程の材料歩留まり80.00 %

投入量と良品出力は同じ生産範囲で測定してください。トリム、不良、立上げロス、回収粉砕材は区別しません。

スクラップ率 =(総投入 − 良品単位重量 × 良品数)÷ 総投入 × 100%

Gross sheet input weight: 1102.3113109243877 lb; Actual good part weight: 0.044092452436975516 lb; Good parts produced: 20000 units → 20.00 %

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

スクラップ率 =(総投入 − 良品単位重量 × 良品数)÷ 総投入 × 100%

The result answers a specific purchasing question: Work out thermoforming scrap rate with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross-input scrap rate in %. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Gross sheet input weight (lb); Actual good part weight (lb); Good parts produced (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross-input scrap rate and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter gross sheet input weight 1,102.31 lb, actual good part weight 0.0441 lb, good parts produced 20,000.00 units. The calculated gross-input scrap rate is 20.00 %. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

シート総投入重量
1,102.31131 lb
実際の良品重量
0.0440924524 lb
生産良品数
20,000 個
Scrap rate = (Gross input − Good part weight × Good quantity) ÷ Gross input × 100%
総投入量に対するスクラップ率20.00 %

よくある質問

Which units should I use for thermoforming scrap rate?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoforming scrap rate results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record gross sheet input weight (lb), actual good part weight (lb), good parts produced (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗