도구 81 / 136

Carton Tooling Amortization Calculator — US Units

Carton Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have cutting die (currency), printing plates (currency), foil tooling (currency) ready before you start.

사양 입력

USD
USD
USD
USD
USD
개

단위 표시만 하며 통화 변환은 하지 않습니다.

입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

카톤당 원가

US$0.00180/carton
카톤 1,000개당 원가US$1.8000/1,000 carton
금형·판 및 설정 총비용US$1,800.00

입력한 전체 수명 수량을 생산한다고 가정합니다. 이후 교체 금형·판은 포함하지 않습니다.

개당 금형비 = (칼형 + 인쇄판 + 박 가공 금형 + 엠보싱 금형 + 기타 준비) ÷ 배분 수량

Cutting die: 1200 USD; Printing plates: 600 USD; Foil tooling: 0 USD; Embossing tooling: 0 USD; Other setup: 0 USD; Expected lifetime cartons: 1000000 units → US$0.00180/carton

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

개당 금형비 = (칼형 + 인쇄판 + 박 가공 금형 + 엠보싱 금형 + 기타 준비) ÷ 배분 수량

The result answers a specific purchasing question: Work out carton tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per carton in your selected currency/carton. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Cutting die (currency); Printing plates (currency); Foil tooling (currency); Embossing tooling (currency); Other setup (currency); Expected lifetime cartons (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per carton and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter cutting die US$1,200.00, printing plates US$600.00, foil tooling US$0.00000, embossing tooling US$0.00000. The calculated cost per carton is US$0.00180/carton. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

절단 금형
1,200 USD
인쇄판
600 USD
박 금형
0 USD
엠보싱 금형
0 USD
기타 설정
0 USD
수명 동안 예상 종이 상자 수
1,000,000 개
Tooling/unit = (Die + Plates + Foil tooling + Embossing tooling + Other setup) ÷ Allocation quantity
카톤당 원가US$0.00180/carton

자주 묻는 질문

Which units should I use for carton tooling amortization?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two carton tooling amortization results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record cutting die (currency), printing plates (currency), foil tooling (currency), embossing tooling (currency) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗