도구 78 / 136

Folding Carton Board Requirement Calculator — US Units

Folding Carton Board Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have good cartons required (units), actual blank width (inch), actual blank length (inch) ready before you start.

사양 입력

개
g/m²
%
입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

필요한 총블랭크 면적

22,660.86 ft²
필요한 총블랭크 재료량1,392.39 lb

실제 블랭크 치수를 사용합니다. 완성 포장의 내부 또는 외부 치수만으로 정확한 칼선 블랭크를 정할 수 없습니다.

손실은 총투입량 중 손실되는 비율입니다. 총필요량 = 양품 산출량 ÷ (1 − 손실 백분율/100)입니다.

선택적 시트 구매는 총블랭크 필요량에 직사각형 자투리를 더합니다.

두 가지 균일한 직사각형 방향만 비교합니다. 간격, 물림 여백, 결 방향 제한 및 불규칙 칼선 중첩 배치는 제외합니다.

Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436

Good cartons required: 10000 units; Actual blank width: 19.68503937007874 inch; Actual blank length: 15.748031496062993 inch; Board GSM: 300 g/m²; Process loss on gross input: 5 %; Sheet width (optional): inch; Sheet length (optional): inch → 22,660.86 ft²

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436

The result answers a specific purchasing question: Work out folding carton board requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross blank area required in ft². Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Good cartons required (units); Actual blank width (inch); Actual blank length (inch); Board GSM (g/m²); Process loss on gross input (%); Sheet width (optional) (inch); Sheet length (optional) (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross blank area required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter good cartons required 10,000.00 units, actual blank width 19.69 inch, actual blank length 15.75 inch, board gsm 300.00 g/m². The calculated gross blank area required is 22,660.86 ft². The table lists the remaining inputs and results so the scenario can be checked or reproduced.

필요 양품 종이 상자 수
10,000 개
실제 전개도 폭
19.6850394 inch
실제 전개도 길이
15.7480315 inch
판지 평량
300 g/m²
총투입량 기준 공정 손실
5 %
시트 폭 (선택)
inch
시트 길이 (선택)
inch
Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436
필요한 총블랭크 면적22,660.86 ft²

자주 묻는 질문

Which units should I use for folding carton board requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two folding carton board requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record good cartons required (units), actual blank width (inch), actual blank length (inch), board gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗