Shrink Sleeve Cost per Unit Calculator — US Units
Shrink Sleeve Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have layflat width (inch), sleeve cut length (inch), film gsm (g/m²) ready before you start.
사양 입력
단위 표시만 하며 통화 변환은 하지 않습니다.
양품 슬리브당 필름 재료 원가
접힌 폭은 펼친 튜브 둘레의 절반이므로 면적은 양면을 포함합니다. 추가 이음 겹침이나 가장자리 절단은 이론 형상 밖입니다.
손실은 총투입량 중 손실되는 비율입니다. 총필요량 = 양품 산출량 ÷ (1 − 손실 백분율/100)입니다.
접합, 인쇄 및 가공 비용은 별도이며 입력한 경우만 반영합니다.
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)
Layflat width: 3.937007874015748 inch; Sleeve cut length: 5.905511811023622 inch; Film GSM: 65 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process loss on gross input: 5 %; Additional seaming / printing / conversion per sleeve: 0 USD/unit → US$0.00616/sleeve입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.
계산식을 알기 쉽게.
The result answers a specific purchasing question: Work out shrink sleeve cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read film material cost per good sleeve in your selected currency/sleeve. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
계산기 사용 방법
- 01
Collect Layflat width (inch); Sleeve cut length (inch); Film GSM (g/m²); Film thickness (mil); Entered film density (g/cm³); Film price on selected basis (currency/lb); Process loss on gross input (%); Additional seaming / printing / conversion per sleeve (currency/unit). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review film material cost per good sleeve and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
검증할 수 있는 계산
For this US purchasing example, enter layflat width 3.94 inch, sleeve cut length 5.91 inch, film gsm 65.00 g/m², film price on selected basis US$1.3608/lb. The calculated film material cost per good sleeve is US$0.00616/sleeve. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 튜브 평폭
- 3.93700787 inch
- 슬리브 절단 길이
- 5.90551181 inch
- 필름 평량
- 65 g/m²
- 선택 기준의 필름 가격
- 1.36077711 USD/lb
- 총투입량 기준 공정 손실
- 5 %
- 슬리브당 추가 접합 / 인쇄 / 가공비
- 0 USD/단위
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)자주 묻는 질문
Which units should I use for shrink sleeve cost per unit?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two shrink sleeve cost per unit results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record layflat width (inch), sleeve cut length (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.
계산 방법, 단위 및 재료 가정 ↗