ИНСТРУМЕНТ 94 / 136

Thermoformed Part Material Weight Calculator — US Units

Thermoformed Part Material Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), machine pitch (inch), parts across (units) ready before you start.

Ваши параметры

шт.
g/m²
Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Валовой расход листового материала на деталь

0,0794 lb/part
Валовая площадь полотна на деталь0,6458 ft²/part
Валовой расход на 1 000 деталей79,37 lb/1,000 parts

Это валовой расход полотна, а не масса готовой детали. Разница включает скелетные обрезки и весь материал вне сохраняемой детали.

Предполагает один ряд деталей по ходу машины на введённый шаг; включите все гнёзда по ширине этого раппорта.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

Web width: 31.496062992125985 inch; Machine pitch: 11.811023622047244 inch; Parts across: 4 units; Sheet GSM: 600 g/m² → 0,0794 lb/part

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoformed part material weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross sheet material allocation per part in lb/part. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Web width (inch); Machine pitch (inch); Parts across (units); Sheet GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross sheet material allocation per part and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter web width 31.50 inch, machine pitch 11.81 inch, parts across 4.00 units, sheet gsm 600.00 g/m². The calculated gross sheet material allocation per part is 0.0794 lb/part. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Ширина полотна
31,496063 inch
Шаг машины
11,8110236 inch
Детали по ширине
4 шт.
Масса листа на м²
600 g/m²
Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436
Валовой расход листового материала на деталь0,0794 lb/part

Частые вопросы

Which units should I use for thermoformed part material weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoformed part material weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), machine pitch (inch), parts across (units), sheet gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗