ИНСТРУМЕНТ 93 / 136

Thermoforming Sheet Weight Calculator — US Units

Thermoforming Sheet Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have sheet / web width (inch), sheet / web length (ft), sheet thickness (mil) ready before you start.

Ваши параметры

g/cm³

Примерная плотность. Используйте фактическую спецификацию полимера или рецептуры.

Типичная плотность. Фактическая зависит от марки и рецептуры полимера. Значение выше можно изменить.

Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Масса листового или рулонного материала

1 190,50 lb
Рассчитанный граммаж листа675,00 g/m²
Площадь листа или полотна8 611,13 ft²

Плотность вводится, а не определяется по готовой детали. Для вспенённых или многослойных листов может потребоваться измеренная эффективная плотность или фактический граммаж.

Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436

Sheet / web width: 31.496062992125985 inch; Sheet / web length: 3280.839895013123 ft; Sheet thickness: 19.68503937007874 mil; Actual or assumed sheet density: 1.35 g/cm³ → 1 190,50 lb

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoforming sheet weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read sheet / web material weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Sheet / web width (inch); Sheet / web length (ft); Sheet thickness (mil); Actual or assumed sheet density (g/cm³). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review sheet / web material weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter sheet / web width 31.50 inch, sheet / web length 3,280.84 ft, sheet thickness 19.69 mil, actual or assumed sheet density 1.35 g/cm³. The calculated sheet / web material weight is 1,190.50 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Ширина листа / полотна
31,496063 inch
Длина листа / полотна
3 280,8399 ft
Толщина листа
19,6850394 мил
Фактическая или принятая плотность листа
1,35 g/cm³
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436
Масса листового или рулонного материала1 190,50 lb

Частые вопросы

Which units should I use for thermoforming sheet weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoforming sheet weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record sheet / web width (inch), sheet / web length (ft), sheet thickness (mil), actual or assumed sheet density (g/cm³) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗