ИНСТРУМЕНТ 95 / 136

Thermoforming Scrap Rate Calculator — US Units

Thermoforming Scrap Rate connects the figures on a US supplier quote with the quantity used by your packaging operation. Have gross sheet input weight (lb), actual good part weight (lb), good parts produced (units) ready before you start.

Ваши параметры

шт.
Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Доля отходов от валового входа

20,00 %
Материал вне годной продукции220,46 lb
Масса годной готовой продукции881,85 lb
Материальный выход процесса80,00 %

Измеряйте вход и годный выход в одних границах производства. Расчёт не различает обрезки, брак, пусковые потери и возвращённый дроблёный материал.

Доля отходов = (Валовой вход − Масса годной детали × Число годных) ÷ Валовой вход × 100%

Gross sheet input weight: 1102.3113109243877 lb; Actual good part weight: 0.044092452436975516 lb; Good parts produced: 20000 units → 20,00 %

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Доля отходов = (Валовой вход − Масса годной детали × Число годных) ÷ Валовой вход × 100%

The result answers a specific purchasing question: Work out thermoforming scrap rate with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross-input scrap rate in %. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Gross sheet input weight (lb); Actual good part weight (lb); Good parts produced (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross-input scrap rate and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter gross sheet input weight 1,102.31 lb, actual good part weight 0.0441 lb, good parts produced 20,000.00 units. The calculated gross-input scrap rate is 20.00 %. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Масса листового сырья брутто
1 102,31131 lb
Фактическая масса годной детали
0,0440924524 lb
Произведённые годные детали
20 000 шт.
Scrap rate = (Gross input − Good part weight × Good quantity) ÷ Gross input × 100%
Доля отходов от валового входа20,00 %

Частые вопросы

Which units should I use for thermoforming scrap rate?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoforming scrap rate results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record gross sheet input weight (lb), actual good part weight (lb), good parts produced (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗