TOOL 64 / 136

Nested Trays per Carton Stack Calculator — US Units

Nested Trays per Carton Stack connects the figures on a US supplier quote with the quantity used by your packaging operation. Have internal carton height (inch), total vertical packing clearance (inch), first tray height (inch) ready before you start.

Your specifications

units
Results update as you edit. Nothing is saved until you choose to.
Live calculation

Maximum trays in one carton stack

99.00 trays
Occupied nested stack height32.83 inch
Unused height after packing clearance0.2362 inch
Cartons required with one stack each102.00 cartons

Assumes one vertical stack per carton. Tray footprint must fit the internal carton length and width separately.

Use the measured additional pitch of each nested tray. Deformation and compression are not modeled.

Usable height = Internal carton height − Total vertical clearance; Trays/stack = floor((Usable height − First tray height) ÷ Nesting pitch) + 1 when the first tray fits

Internal carton height: 33.46456692913386 inch; Total vertical packing clearance: 0.39370078740157477 inch; First tray height: 1.968503937007874 inch; Additional nesting pitch: 0.31496062992125984 inch; Trays to pack: 10000 units → 99.00 trays

Calculated from your inputs. Confirm specifications with your supplier.

The formula, made clear.

Usable height = Internal carton height − Total vertical clearance; Trays/stack = floor((Usable height − First tray height) ÷ Nesting pitch) + 1 when the first tray fits

The result answers a specific purchasing question: Work out nested trays per carton stack with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read maximum trays in one carton stack in trays. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

How to use this calculator

  1. 01

    Collect Internal carton height (inch); Total vertical packing clearance (inch); First tray height (inch); Additional nesting pitch (inch); Trays to pack (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review maximum trays in one carton stack and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

A calculation you can check

For this US purchasing example, enter internal carton height 33.46 inch, total vertical packing clearance 0.3937 inch, first tray height 1.97 inch, additional nesting pitch 0.3150 inch. The calculated maximum trays in one carton stack is 99.00 trays. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Internal carton height
33.4645669 inch
Total vertical packing clearance
0.393700787 inch
First tray height
1.96850394 inch
Additional nesting pitch
0.31496063 inch
Trays to pack
10,000 units
Usable height = Internal carton height − Total vertical clearance; Trays/stack = floor((Usable height − First tray height) ÷ Nesting pitch) + 1 when the first tray fits
Maximum trays in one carton stack99.00 trays

Frequently asked questions

Which units should I use for nested trays per carton stack?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two nested trays per carton stack results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record internal carton height (inch), total vertical packing clearance (inch), first tray height (inch), additional nesting pitch (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Check the displayed formula, units and assumptions before using the result.

Method, units and material assumptions ↗