Nested Trays per Carton Stack Calculator — US Units
Nested Trays per Carton Stack connects the figures on a US supplier quote with the quantity used by your packaging operation. Have internal carton height (inch), total vertical packing clearance (inch), first tray height (inch) ready before you start.
您的规格参数
纸箱单垛最多托盘数
假设每箱一垛竖直堆叠。托盘底面必须分别满足纸箱内部长度和宽度。
使用每个套叠托盘的实测增高量。不模拟变形和压缩。
可用高度 = 箱内高 − 总竖向间隙;每堆数量 = 向下取整((可用高度 − 首盘高度)÷ 套叠增量)+ 1,前提是首盘可放入
Internal carton height: 33.46456692913386 inch; Total vertical packing clearance: 0.39370078740157477 inch; First tray height: 1.968503937007874 inch; Additional nesting pitch: 0.31496062992125984 inch; Trays to pack: 10000 units → 99.00 trays根据您输入的数据计算。请与供应商确认规格。
公式解释。
The result answers a specific purchasing question: Work out nested trays per carton stack with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read maximum trays in one carton stack in trays. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
如何使用此计算器
- 01
Collect Internal carton height (inch); Total vertical packing clearance (inch); First tray height (inch); Additional nesting pitch (inch); Trays to pack (units). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review maximum trays in one carton stack and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
可以核验的计算
For this US purchasing example, enter internal carton height 33.46 inch, total vertical packing clearance 0.3937 inch, first tray height 1.97 inch, additional nesting pitch 0.3150 inch. The calculated maximum trays in one carton stack is 99.00 trays. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 纸箱内高
- 33.4645669 inch
- 总垂直包装间隙
- 0.393700787 inch
- 首只托盘高度
- 1.96850394 inch
- 额外嵌套节距
- 0.31496063 inch
- 待装箱托盘数
- 10,000 件
Usable height = Internal carton height − Total vertical clearance; Trays/stack = floor((Usable height − First tray height) ÷ Nesting pitch) + 1 when the first tray fits常见问题
Which units should I use for nested trays per carton stack?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two nested trays per carton stack results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record internal carton height (inch), total vertical packing clearance (inch), first tray height (inch), additional nesting pitch (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
使用结果前,请核对显示的公式、单位和假设。
方法、单位和材料假设 ↗