Remaining Film on Roll Calculator — US Units
Remaining Film on Roll connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.
您的规格参数
测量卷芯外径,而非内孔直径。
如有供应商提供的实际克重或实测克重,请优先使用。
估算剩余长度
几何估算:假设厚度均匀、卷绕紧实且无夹带空气。实际展开长度可能不同。
使用卷芯外径,不能用标称内孔直径代替。
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12
Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 3,684.77 ft根据您输入的数据计算。请与供应商确认规格。
公式解释。
The result answers a specific purchasing question: Work out remaining film on roll with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated remaining length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
如何使用此计算器
- 01
Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review estimated remaining length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
可以核验的计算
For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated remaining length is 3,684.77 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 卷材外径
- 13.7795276 inch
- 卷芯外径
- 3.54330709 inch
- 薄膜厚度
- 3.1496063 密耳
- 幅宽
- 31.496063 inch
- 薄膜克重
- 80 g/m²
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12常见问题
Which units should I use for remaining film on roll?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two remaining film on roll results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
使用结果前,请核对显示的公式、单位和假设。
方法、单位和材料假设 ↗