ツール 81 / 136

Carton Tooling Amortization Calculator — US Units

Carton Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have cutting die (currency), printing plates (currency), foil tooling (currency) ready before you start.

仕様を入力

USD
USD
USD
USD
USD
個

単位表示のみです。為替換算は行いません。

入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

カートン1個当たりの原価

US$0.00180/carton
カートン1,000個当たりの原価US$1.8000/1,000 carton
金型・版代と段取り費の合計US$1,800.00

入力した生涯数量を生産する前提です。後の交換金型・版代は含みません。

1個の金型費 =(抜き型 + 印刷版 + 箔押し型 + エンボス型 + その他段取り)÷ 配賦数量

Cutting die: 1200 USD; Printing plates: 600 USD; Foil tooling: 0 USD; Embossing tooling: 0 USD; Other setup: 0 USD; Expected lifetime cartons: 1000000 units → US$0.00180/carton

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

1個の金型費 =(抜き型 + 印刷版 + 箔押し型 + エンボス型 + その他段取り)÷ 配賦数量

The result answers a specific purchasing question: Work out carton tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per carton in your selected currency/carton. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Cutting die (currency); Printing plates (currency); Foil tooling (currency); Embossing tooling (currency); Other setup (currency); Expected lifetime cartons (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per carton and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter cutting die US$1,200.00, printing plates US$600.00, foil tooling US$0.00000, embossing tooling US$0.00000. The calculated cost per carton is US$0.00180/carton. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

抜き型
1,200 USD
印刷版
600 USD
箔押し金型
0 USD
エンボス金型
0 USD
その他の段取り
0 USD
寿命全体の予定紙器数
1,000,000 個
Tooling/unit = (Die + Plates + Foil tooling + Embossing tooling + Other setup) ÷ Allocation quantity
カートン1個当たりの原価US$0.00180/carton

よくある質問

Which units should I use for carton tooling amortization?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two carton tooling amortization results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record cutting die (currency), printing plates (currency), foil tooling (currency), embossing tooling (currency) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗