Folding Carton Board Requirement Calculator — US Units
Folding Carton Board Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have good cartons required (units), actual blank width (inch), actual blank length (inch) ready before you start.
仕様を入力
必要な総ブランク面積
実際のブランク寸法を使用します。完成包装の内寸や外寸から正確な抜き型展開寸法は確定できません。
ロスは総投入量のうち失われる割合です。総必要量=良品出力÷(1-ロス百分率/100)。
任意のシート購入では、総ブランク必要量に長方形の端材を加算します。
均一な長方形配置を2方向のみ比較します。溝間隔、くわえ代、紙目制約、不規則な抜き型のネスティングは含みません。
Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436
Good cartons required: 10000 units; Actual blank width: 19.68503937007874 inch; Actual blank length: 15.748031496062993 inch; Board GSM: 300 g/m²; Process loss on gross input: 5 %; Sheet width (optional): inch; Sheet length (optional): inch → 22,660.86 ft²入力値に基づく計算です。仕様は仕入先に確認してください。
計算式をわかりやすく。
The result answers a specific purchasing question: Work out folding carton board requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross blank area required in ft². Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
この計算ツールの使い方
- 01
Collect Good cartons required (units); Actual blank width (inch); Actual blank length (inch); Board GSM (g/m²); Process loss on gross input (%); Sheet width (optional) (inch); Sheet length (optional) (inch). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review gross blank area required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
検算できる計算例
For this US purchasing example, enter good cartons required 10,000.00 units, actual blank width 19.69 inch, actual blank length 15.75 inch, board gsm 300.00 g/m². The calculated gross blank area required is 22,660.86 ft². The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 必要な良品紙器数
- 10,000 個
- 実際のブランク幅
- 19.6850394 inch
- 実際のブランク長さ
- 15.7480315 inch
- 板紙坪量
- 300 g/m²
- 総投入量基準の工程ロス
- 5 %
- シート幅(任意)
- inch
- シート長さ(任意)
- inch
Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436よくある質問
Which units should I use for folding carton board requirement?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two folding carton board requirement results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record good cartons required (units), actual blank width (inch), actual blank length (inch), board gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
結果を使用する前に、表示された式、単位、前提条件を確認してください。
計算方法・単位・材料の前提条件 ↗