Shrink Sleeve Cost per Unit Calculator — US Units
Shrink Sleeve Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have layflat width (inch), sleeve cut length (inch), film gsm (g/m²) ready before you start.
仕様を入力
単位表示のみです。為替換算は行いません。
良品スリーブ1個当たりのフィルム材料原価
折幅は開いた筒の周長の半分なので、面積は両面を含みます。追加の継ぎ目重なりや端部トリムは公称形状に含みません。
ロスは総投入量のうち失われる割合です。総必要量=良品出力÷(1-ロス百分率/100)。
継ぎ加工、印刷、加工費は入力した場合のみ別途含みます。
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)
Layflat width: 3.937007874015748 inch; Sleeve cut length: 5.905511811023622 inch; Film GSM: 65 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process loss on gross input: 5 %; Additional seaming / printing / conversion per sleeve: 0 USD/unit → US$0.00616/sleeve入力値に基づく計算です。仕様は仕入先に確認してください。
計算式をわかりやすく。
The result answers a specific purchasing question: Work out shrink sleeve cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read film material cost per good sleeve in your selected currency/sleeve. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
この計算ツールの使い方
- 01
Collect Layflat width (inch); Sleeve cut length (inch); Film GSM (g/m²); Film thickness (mil); Entered film density (g/cm³); Film price on selected basis (currency/lb); Process loss on gross input (%); Additional seaming / printing / conversion per sleeve (currency/unit). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review film material cost per good sleeve and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
検算できる計算例
For this US purchasing example, enter layflat width 3.94 inch, sleeve cut length 5.91 inch, film gsm 65.00 g/m², film price on selected basis US$1.3608/lb. The calculated film material cost per good sleeve is US$0.00616/sleeve. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- チューブ折径
- 3.93700787 inch
- スリーブのカット長
- 5.90551181 inch
- フィルム坪量
- 65 g/m²
- 選択基準のフィルム価格
- 1.36077711 USD/lb
- 総投入量基準の工程ロス
- 5 %
- スリーブあたりの追加シーム・印刷・加工費
- 0 USD/単位
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)よくある質問
Which units should I use for shrink sleeve cost per unit?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two shrink sleeve cost per unit results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record layflat width (inch), sleeve cut length (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
結果を使用する前に、表示された式、単位、前提条件を確認してください。
計算方法・単位・材料の前提条件 ↗