도구 94 / 136

Thermoformed Part Material Weight Calculator — US Units

Thermoformed Part Material Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), machine pitch (inch), parts across (units) ready before you start.

사양 입력

개
g/m²
입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

부품당 총시트 재료 배부량

0.0794 lb/part
부품당 총원단 면적0.6458 ft²/part
부품 1,000개당 총배부량79.37 lb/1,000 parts

총원단 배부량이며 완성 부품 중량이 아닙니다. 차이에는 골격 자투리와 유지 부품 외 모든 재료가 포함됩니다.

입력 피치당 기계 방향 부품 한 행을 가정합니다. 해당 반복 폭의 모든 캐비티를 포함하세요.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

Web width: 31.496062992125985 inch; Machine pitch: 11.811023622047244 inch; Parts across: 4 units; Sheet GSM: 600 g/m² → 0.0794 lb/part

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoformed part material weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross sheet material allocation per part in lb/part. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Web width (inch); Machine pitch (inch); Parts across (units); Sheet GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross sheet material allocation per part and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter web width 31.50 inch, machine pitch 11.81 inch, parts across 4.00 units, sheet gsm 600.00 g/m². The calculated gross sheet material allocation per part is 0.0794 lb/part. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

원단 폭
31.496063 inch
기계 피치
11.8110236 inch
폭 방향 부품 수
4 개
시트 평량
600 g/m²
Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436
부품당 총시트 재료 배부량0.0794 lb/part

자주 묻는 질문

Which units should I use for thermoformed part material weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoformed part material weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), machine pitch (inch), parts across (units), sheet gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗