Thermoforming Sheet Weight Calculator — US Units
Thermoforming Sheet Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have sheet / web width (inch), sheet / web length (ft), sheet thickness (mil) ready before you start.
사양 입력
예시 밀도입니다. 실제 폴리머 또는 배합 규격을 사용하세요.
대표 밀도입니다. 실제 밀도는 수지 등급과 배합에 따라 달라집니다. 위 값을 수정할 수 있습니다.
시트 또는 원단 재료 중량
밀도는 입력값이며 완성 부품에서 추정하지 않습니다. 발포 또는 다층 시트는 실측 유효 밀도나 실제 평량이 필요할 수 있습니다.
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436
Sheet / web width: 31.496062992125985 inch; Sheet / web length: 3280.839895013123 ft; Sheet thickness: 19.68503937007874 mil; Actual or assumed sheet density: 1.35 g/cm³ → 1,190.50 lb입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.
계산식을 알기 쉽게.
The result answers a specific purchasing question: Work out thermoforming sheet weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read sheet / web material weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
계산기 사용 방법
- 01
Collect Sheet / web width (inch); Sheet / web length (ft); Sheet thickness (mil); Actual or assumed sheet density (g/cm³). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review sheet / web material weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
검증할 수 있는 계산
For this US purchasing example, enter sheet / web width 31.50 inch, sheet / web length 3,280.84 ft, sheet thickness 19.69 mil, actual or assumed sheet density 1.35 g/cm³. The calculated sheet / web material weight is 1,190.50 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 시트 / 원단 폭
- 31.496063 inch
- 시트 / 원단 길이
- 3,280.8399 ft
- 시트 두께
- 19.6850394 밀
- 실제 또는 가정한 시트 밀도
- 1.35 g/cm³
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436자주 묻는 질문
Which units should I use for thermoforming sheet weight?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two thermoforming sheet weight results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record sheet / web width (inch), sheet / web length (ft), sheet thickness (mil), actual or assumed sheet density (g/cm³) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.
계산 방법, 단위 및 재료 가정 ↗