도구 95 / 136

Thermoforming Scrap Rate Calculator — US Units

Thermoforming Scrap Rate connects the figures on a US supplier quote with the quantity used by your packaging operation. Have gross sheet input weight (lb), actual good part weight (lb), good parts produced (units) ready before you start.

사양 입력

개
입력값을 수정하면 결과가 갱신됩니다. 저장을 선택하기 전에는 저장되지 않습니다.
실시간 계산

총투입량 기준 스크랩률

20.00 %
양품 산출에 포함되지 않은 재료220.46 lb
양품 완제품 산출 중량881.85 lb
공정 재료 수율80.00 %

투입량과 양품 산출량은 같은 생산 경계에서 측정하세요. 이 계산은 절단 자투리, 불량, 시동 손실 또는 회수 분쇄재를 구분하지 않습니다.

폐기율 = (총투입 − 양품 개당 중량 × 양품 수량) ÷ 총투입 × 100%

Gross sheet input weight: 1102.3113109243877 lb; Actual good part weight: 0.044092452436975516 lb; Good parts produced: 20000 units → 20.00 %

입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.

계산식을 알기 쉽게.

폐기율 = (총투입 − 양품 개당 중량 × 양품 수량) ÷ 총투입 × 100%

The result answers a specific purchasing question: Work out thermoforming scrap rate with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross-input scrap rate in %. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

계산기 사용 방법

  1. 01

    Collect Gross sheet input weight (lb); Actual good part weight (lb); Good parts produced (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross-input scrap rate and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

검증할 수 있는 계산

For this US purchasing example, enter gross sheet input weight 1,102.31 lb, actual good part weight 0.0441 lb, good parts produced 20,000.00 units. The calculated gross-input scrap rate is 20.00 %. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

시트 총투입 중량
1,102.31131 lb
실제 양품 부품 중량
0.0440924524 lb
생산된 양품 부품 수
20,000 개
Scrap rate = (Gross input − Good part weight × Good quantity) ÷ Gross input × 100%
총투입량 기준 스크랩률20.00 %

자주 묻는 질문

Which units should I use for thermoforming scrap rate?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoforming scrap rate results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record gross sheet input weight (lb), actual good part weight (lb), good parts produced (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗